Рейтинг@Mail.ru

COLD GLUE LABELING EQUIPMENT

Linear machine cold glue 3000-6500 bph

Capacity:                     

3000-6500 bph

Typology:

Cold glue

Label type:

Paper

1 position

 

 

Type

Ø

Bott.

(mm)

Max

Label

Length

(mm)

Prod.

B/H

Electrics

Air

Consumpt

ION

Net

Weight

(Kg)

Inverter

Heater

Star

block

product

satin

glue

auto

Pump

glue

Uno WA

45-120

330

3.000

380V ac Triple Pbase+ Neutral50Hz 0.7 Kw

60

Liter/min

6 Bar

550

S

O

 

S

S

Uno WA Super

45-110

 

 

380V ac Triple Pbase+ Neutral50Hz 0.7 Kw

50

Liter/min

6 Bar

550

S

O

S

S

S

Base made of stainless steel with skeleton made of steel profiles.
  • Paneling and removable parts made of stainless steel
  • Conveyor belt and casing made of stainless steel
  • Stopping device in case of jamming.
  • Timing screw conveyor
  • The distribution of the glue is given by the rubber gluing roll equipped with a scraper having automatic glue film adjustment by a pneumatic device.
The labelling unit consist of:
  • Oscillating labels holding magazine, aluminum roll with horizontal strip gluing profiles.
  • Fingers unit with stainless steel blades comb for a direct transfer of the label on the container.

Pneumatic glue pump type “C 7” 
Stretching unit with pulleys, belts and rolling wall made of special anti-acid foam rubber.
The central drive is transmitted by a gear reducer controlled by the inverter. Manual speed adjustment.

OPTIONALS

    • Motor drive head of conveyor with fixed or variable speed (by inverter)
    • Automatic speed adjustment according to the input and output photocells
    • Protections against the accidents by stainless steel boards and Plexiglas boards according to “CE”regulations . Microswitch signalling the alarm for doors opening.
    • Printing unit with ink and perforating needle type or ink-jet.
    • Others on request

Mechanical orientation

The automatic mechanical orientation is applicable to containers with a cylindrical cross section. The first orientation device is the simplest and the cheapest. The orientation takes place on the labeller infeed star.

 
A mechanical arrangement (a spring loaded lever) hunts and catches the container (which can be only cylindrical), by a spotting notch or bar moulded into the lower side wall area.
The bottle held in the required position is transferred on to the carousel plates. The degree of accuracy which is possible to have using this mechanical device is good but not the best possible.

The same device is used to orientate a cylindrical container according to its handle where the handle subsitute the spotting notch for feature. A second type of orientation takes place on each carousel plates. In this case the bottle centring platform is made up of two sections: an inner rotating section and a fixed outer section. The container, always cylindrical, needs to have a spotting bar on its bottom. The bottle goes onto the plate (which at this stage, has the two sections at the same level) and, once that it is clamped firmly against the fixed auter plate section by means of pressure from the descending centring bell, the rotating inner plate section is held down via cam operated stirrup, enabling the spring loaded hunting lever to touch the bottle bottom. Then, by spinning the bottle around 360°, the lever catches the spotting bar. When the lever is into the spotting bar il will drag the bottle in the required position, ready to receive its labels.
In few cases the cylindrical container have letters, scales, figures in relief but no spotting bar or notch. NUOVA BRB has an orientation device solutions also for these special packages.

Through a mechanical sensor and a system of levers which increases the sensor sensitivity the device is able to detect a 3/10 of millimetre relief.
Moreover by positioning the lever on the machine carousel dish and by installing another very simple mechanical device, this system is not sensitive to containers eccentricity.

 

Opto electronic orientation

This type of orientation device is more sophisticated than the mechanical one and it is designed for medium and high output rate and orientation feature different from that previously exposed. The orientation through luminescence sensors can sense marks which can be a color dot (like on champagne capsules with product name printed vertically) or the seam of a can or any other significative color texture. These marks are detected by a fiber optic sensor which can “see” the mark from the type of light which, shooted by the fiber optic, hit by the container, goes back to the photo cell. The orientation takes place on each carousel plates.The plates, which can be driven by clutch brakes system, stepper motors, or brushless, rotate until the photocell detect the mark and interrupt container rotation. At that point plates are ready to handle the container in the position required for the label applications.

By using another type of luminescence photo cell or camera it is possible to detect also ribs on plastic containers (ribs are made especially on containers for aesthetic purposes or for increasing the grip of the surface which has to be grab by the consumers).

Excise stamp application (tax label L, U shape)

BRB Globus rotary labelling machines can apply excise stamp U and L shaped with cold glue and tamper evident or guarantee L shaped self-adhesive labels.
By means of an original and highly reliable outfeed star, the excise stamp, previously applied on the bottle neck in vertical position,is taken down to the cap (in case of excise stamp or security L, or to the cap and the other side of the neck (in case of excise stamp U shaped).





EXPLORE ANOTHER EQUIPMENT: