Логистика мясных предприятий

Главная | Решение для мясной промышленности |Убой МРС | Логистика мясных предприятий

Логистика мясных предприятий

Made of a tubular guide rail attached to the dock rail with a hinge. There is a 01 VT or Ø 2” tube inside which can be folded or unfolded. At the free end there is a hook that can be attached to the cart rail.

Vertical movement: 90°.
Horizontal movement: 20°.

OPERATION: 

  • Guide the telescopic section towards the cart rail.
  • Extend it until it reaches the cart rail, then attach it.
  • Start unloading.

 

RAIL TYPE

Dual rail telescopic section

Tubular telescopic section Ø 1 ½”

Tubular telescopic section Ø 2”

 

0.00 KZT

Used to load/unload the meat, up to 300 kilos maximum. CHARACTERISTICS:

  • Maximum length: 2980 mm.
  • Useful length: 1860 mm.
  • Minimum height: 820 mm.
  • Maximum height: 2680 mm.
  • Powered by hydraulics.
  • Power: 2.5 KW.
  • Voltage; 3 phase 380 V.
  • Electrical circuit: 24 V.
  • Moving angle of the turning column: 320°.
  • Moving angle of the central arm: 260°.
  • Combined vertical movement for tilting and height.
  • Raising and lowering speed for the hook: 0.3 m/s.
  • Attached to the floor on a 400x400 mm base.

Made of AISI-304 stainless steel

 

0.00 KZT

Machine to load and unload meat onto a refrigerated lorry, using a rotating column. CHARACTERISTICS:

  • Load capacity: 180 kilos.
  • Maximum length: 2260 mm.
  • Useful length: 2000 mm.
  • Minimum height: 400 mm.
  • Maximum height: 2400 mm.
  • Powered by hydraulics.
  • Power: 800 W.
  • Voltage: 12 or 24 V.
  • Combined vertical movement for tilting and height.
  • Moving angle of the turning column: 270®.
  • Moving angle of the central arm: 270°.
  • Hook rotating angle: 130®
    • Total useful rotation angle: 360°.
    • Raising and lowering speed for the hook: 0.16 m/s.
  • Fixed: attached to the isothermal body structure.
  • Machine weight: 60 kilos.

Structure made of aluminum alloy. Hook and control knob made of stainless steel.

 

0.00 KZT

This system is placed on the outside of the dock and is embedded within the loading device.

It includes:

  • Support structure, made of 2 columns with plates that can be screwed into the floor and an upper beam between the columns. Made of hot-dip galvanised steel.
  • Electric chain hoist that can hold up to 250 kilos, with a special stainless steel hook to hang the animal from.
  • Manually controlled cart, to allow the hoist to slide along the support beam.

 OPERATION:

  • The hoist chain can be moved manually until It hangs inside the cart using the hook.
  • The channel can be raised using the control panel for the hoist.
  • When the channel is at the same height as the dock rails, hang the channel in the empty hook.

*NOTE: This system can only be set up if the dock door is at least 500 mm higher that the tread level.

 

0.00 KZT

Used to raise up the channels from the cart rail to the dock rail.

Made up of:

  • A mobile stretch of rail.
  • A series of hinges to attach the mobile rail to the fixed rail.
  • A series of stops on the ends, to stop the hooks from falling.
  • An electrical chain hoist that can lift up to 250 kilos, to raise and lower the rail section.
  • A clamp to attach the hoist to the support beam.

The mobile rail can be one of the following types:

  • An aluminum dual rail: with 3 supports made of stainless steel sheets with a ring to support the hoist hook.
  • Galvanised steel tube (Ø 1 ½” or Ø 2”): with a support on each end, both with a ring to support the hoist hook.

Speed: 210 hooks/hour. 

RAIL TYPE

With a dual rail

With a tubular track Ø 1 ½”

With a tubular track Ø 2”

 

0.00 KZT

System used to raise the hooks from the level of the cart to the level of the dock rails.

Made up of:

  • A telescopic section to join the cart rail with the height change rail.
  • An inserter at the entrance to the height change mechanism, powered pneumatically, which allows hooks to enter one by one on the chain.
  • Closed Ø 1 ¼” chain circuit.
  • UPN-60 profile guides.
  • Tubular dual rail, either Ø 1 ½” or Ø 2”.
  • Pushers with 4 nylon wheels.
  • Powered by a 1.1 KW gear motor.
  • Electrical control panel.
  • Buttons to control the different mechanisms, with stop and start switches.

Made of hot-dip galvanised steel.

Speed: 720 hooks/hour.

OPERATION:

  • It joins the telescopic section to the cart rail, so that the hooks slide on up to the pneumatic inserter.
  • The hooks automatically enter the inserter in between the pushers that are part of the height change mechanism.
  • The pushers on the height change mechanism drag the hooks to the height of the dock rail.

 

0.00 KZT

Made of 2 tube guide rails with two handrails that can be folded or unfolded. At each there are several mushroom-shaped stops to support it on the track.

Made of AISI-304 stainless steel.
Horizontal movement: 20°.

OPERATION:

  • Hang the telescopic section from the handrails on the dock rail,
  • Extend the telescopic section until it reaches the cart rail.
  • Hang it from the handrails on the cart rail.
  • Start unloading,
0.00 KZT
Мультилинии производства макаронных изделий

Мультилинии производства макаронных изделий