Slaughter
line sheep

Main | Slaughter houses deboning rooms | Slaughter
line sheep

Slaughter
line sheep

This should be set up before the animals enter the pens, to inspect them before they are slaughtered. Made up of:

  • 2 kick boards.
  • 1 double one-way door.
  • 1 door with 2 swinging doors that block any possible exit.
  • system to hold the head in place to carry out the inspection.
  • lateral walkway to allow the operator to carry out the inspection easily from above.

Walkway made of galvanised steel.

0.00 KZT

Used for the animal pens in the slaughterhouse.

They are supported by the columns that make up the pen, with a swinging door that is attached to the column with hinges and a latch that closes on the opposite pillar.

The exact measurements and shape of the pen will depend on the type of animal being held.

  • For pigs, fences are made of metal sheets.
  • For sheep, metal sheets are used for smaller animals, while vertical bars are used for larger animals.
  • For calves, horizontal bars are used.
  • For fences used to create pens for several different animals (pigs, sheep and cows), vertical bars or metal sheets are used up to a certain height, then horizontal bars are used up to 1500 mm high.

The bars are made of galvanised steel or AISI-304 stainless steel.

0.00 KZT

Used to close the animal pens in the slaughterhouse.

Made of:

  • Structural columns that are bolted to the floor, spaced 2000 mm apart from each other.
  • Space between the fences to screw or bolt between the columns. Can be made of either metal sheets or bars. Made up of different units, allowing a unit to be easily replaced if necessary. The pens are very versatile, as spaces can be made larger or smaller by adding or removing different units.
  • The exact measurements and shape of the pen will depend on the type of animal being held.
  • For pigs, fences are made of metal sheets.
  • For sheep, metal sheets are used for smaller animals, while vertical bars are used for larger animals.
  • For calves, horizontal bars are used.
  • For fences used to create pens for several different animals (pigs, sheep and cows), vertical bars or metal sheets are used up to a certain height, then horizontal bars are used up to 1500 mm high.

The bars are made of galvanised steel or AISI-304 stainless steel. 

0.00 KZT

This machine is used to push sheep along the corral from the feeding area to the restrainer.

Made of:

  • 1400mm high panel with supporting frame, which moves horizontally and vertically.
  • Passageway with two side latches 1500 mm high, sheet metal panel.
  • Sheet metal entry doors, which open on either side, so that the animals to fill the passageway where pushing panel is (number of doors depends on the facility).
  • Doors for staff to enter the restrainer area (number of doors depends on the facility).
  • Two IPN rails in the passageway, placed at 2100 mm from the floor, with a toothed rack for the panel to move along.
  • Carts that drag the panel and run along the rack, driven by a gear motor (power depending on the facility).
  • Pneumatic system to raise up the panel as it moves back.
  • Upper rail for electrical and pneumatic cables.
  • Control panel that controls any variations in speed.
  • 2 panels of buttons with manual switches to raise, lower and stop the barrier, as well as to move it forwards and backwards.
  • 2 limit switches to stop the panel along its horizontal axis.
  • 2 limit switches to stop the panel along its vertical axis.
  • 2 limit switches to balance the panel along its vertical axis.

Total measurements and length: depends on the facilities.

 

0.00 KZT

Entry passage leading to the stunning area. Made of two 1000 mm high fences, which are parallel to each other, leaving space for the animals to pass through. Each fence has columns with plaques that can be screwed into the floor, with a sheet metal platform.

Made of galvanised steel.

0.00 KZT

System of rotating doors where the sheep enter, which leads to the restrainer or similar.

Made up of:

  • Central column that the rotating doors are attached to.
  • Fences that form a circular pen.
  • Entrance for the animals.
  • Direct exist to the stunning area.

The rotating system can be operated manually or using a 0.55 KW motor (which works using a pedal). The movement of the circular fence forces the sheep to move into the stunning area.

Made of galvanised steel.

 

0.00 KZT

Used to restrain the animal while it is stunned via electrical anesthesia.

Made up of:

  • Box measuring 800 mm long x 500 mm wide x 700 mm high.
  • Guillotine doors at the entrance, which work using a pneumatic piston and are operated with a manual valve.
  • There is a hole in the lid to restrain the animal’s head and go ahead with the stunning.
  • Doors at the side, which work using a pneumatic piston and are operated with a manual valve.
  • Constructed on 300 mm legs with plaques on the bottom to anchor them to the floor. This allows the animal to fall and for it to be bled.
  • Protective inner plastic that prevents electrical conduction and ensures the animal is properly stunned

Made of stainless steel AISI304

 

0.00 KZT

In order to transport and restrain the animal as it moves from the entrance to the stunning area, for Halal slaughter.

Made up ot:

  • 2 metal strips to support the animals, placed vertically and operated using 2 1.1 KW gear motors.
  • Fixed position width regulator for the passageway, adjusted with pins.
  • Lower gutter to collect the blood.
  • There is no gutter for the final 500mm, with a system to wash the metal strips
  • Control panel for the gears that controls any variations in speed.

Made of stainless steel AISI304

Descripton of work with HALAL method

The animals enter the restrainer, their throats are cut. the blood is collected in the lower gutter as they move forward, and the carcasses are hung up once they are released from the restrainer.

 

0.00 KZT

In order to transport and restrain the animal as it moves from the entrance to the stunning area. Made up of:

  • 2 PVC bands to support the animals, placed vertically and operated using 2 1.5 KW gear motors.
  • The width of the bands can be adjusted to fit the size of the animal.
  • Lower passageway.
  • Control panel for the gears that controls any variations in speed.

Made of galvanised steel.

  • Width adjustment operated with pneumatic pistons:
  • Direction V operated manual
  • Adjust the height of the lower passageway FIXED
  • Stop and start button, and individual buttons for each one of the movements that adjust the belts and lower passageway by pneumatic psiton
  • Made of stainless steel AISI304

 

0.00 KZT

In order to transport and restrain the animal as it moves from the entrance to the stunning area. Made up of:

  • 2 PVC bands to support the animals, placed vertically and operated using 2 1.5 KW gear motors.
  • The width of the bands can be adjusted to fit the size of the animal.
  • Lower passageway.
  • Control panel for the gears that controls any variations in speed.

Made of galvanised steel.

  • Width adjustment operated with 5 hydraulic  pistons:
    1. open the passageway on the left
    2. open the passageway on the right
    3. close the passageway on the left
    4. close the passageway on the right
    5. adjust the direction of the band
  • Direction V operated with a hydraulic piston
  • Adjust the height of the lower passageway operated with 1 hydraulic piston raise or lower the ramp
  • Stop and start button, and individual buttons for each one of the movements that adjust the belts and lower passageway

Made of stainless steel AISI304, chassis made of galvanised steel

 

 

0.00 KZT

Located at the end of the restraining and stunning system (whether a restrainer or a restraining box is used).
This consists of a table with rollers and wings at the sides for the sheep carcass to fall on while it waits to be hung on the bleeding rail.
Made of stainless steel.

0.00 KZT

This machine is placed at the exit to the stunning area, which allows the animal to be bled horizontally and also for the animals to be transferred onto the bleeding rail.

Description:

  • Tubular chassis, legs adjustable with a tuning wrench.
  • 2 parallel chains joined together with red polyethylene sheets, which act as a conveyor belt.
  • Spray nozzles for cleaning the band.
  • Lower hopper shaped like an inverted V with a side gutter on one side to collect the blood, and a gutter on the other side to collect urine and excrement.
  • Electrical control panel with stop and start buttons.
  • Electrical speed controller.

Made of AISI-304 stainless steel.

 

0.00 KZT

Located in the skinning area and used to prepare skin before it enters the skinner.
Consists of:

  • Nozzle that pulls the animal’s skin, operated by a pneumatic piston operated by using a pedal.
  • Strengthened sterilizer for the nozzle.

Made of stainless steel AISI 304 

0.00 KZT

Sheep skinner DSX

Discription

  • Made of stainless-steel.
  • Roller in stainless-steel with length 500mm.
  • Handy work saving.
  • Structure fixed on the floor.
  • Electrical control panel is included
0.00 KZT

Machine designed to skin sheep easily, made up of:

  • A vertical rail with a cart that is powered by a hydraulic piston, 1350 mm long.
  • A fixed clip attached to the cart, which opens and closes automatically to grab and roll the animal skin.
  • Rotating hydraulic motor to turn the clip.
  • Powered by a hydraulic unit with a supporting frame, solenoid valves and connecting hoses between the hydraulic unit and the hydraulic pistons.
  • Electrical control panel.

Made of AISI-304 stainless steel.

The arm movements are adjustable, and the following can be modified:

  • Raising speed
  • Lowering speed
  • Rolling speed
  • Unrolling speed

Operation:

To start with, the arm is on the upper part of the machine. The animal arrives with the skin slightly removed. The operator places the skin in the open clip. When the start button is pressed the clip closes, turns and moves down, rolling up the skin around the arm. When the arm reaches the bottom, the skin is completely removed and rolled around the arm. Next, the arm raises up and unrolls the skin until it reaches the upper position.

 

0.00 KZT