Find

Due to the fact that it is expensive and sometimes difficult to carry out installations and assembly in the offshore industry, it is sensible to do as much of the assembly and testing off-site as possible.   

The shown plant is mounted on an epoxy-coated, construction iron skid with drip tray.

The plant is designed for 9 m³/h and consists of filter bags for removal of mechanical impurities, scavenger plant for removal of organic, suspended matter, demineralization plant, plant for neutralization of regeneration chemicals, and a central electric control cabinet.

The automation for sliding doors SC type is based in a system with motorgear, thanks to the worm reduction gear, the door is manually-movable in case of power failure.

The motion transmission between the door leaf and the motorgear is via a toothed belt. The control box is made in white anti-corrosion IP65 ABS. The connections between the control and the motor are pre-wired thanks to a fast strong connector in the lower part of the ABS box.

The control software is an Incold exclusivity. The operating voltage is 220V, 50 Hz. The control of the door leaf positioning is controlled by an encoder installed in the motorgear. The adjustment of the door speed is controlled by an inverter and an encoder. A color display with

Touch screen technology, installed on the external side of the control box, allows to control the opening and closing of the door. Through the display you can easily adjust and control the door functions such as speedy, acceleration/ deceleration ramps, partial opening, automatic reclosing, count of the openings, status of the safety devices. The main crush-prevention safety device is a sensitive bar resistant type located on the vertical edge of the door leaf which, in case of collision with an obstacle, instantly blocks the door and reverses the motion, sending a signal to the panel by means of wireless system.

A “transmitter-receiver” photocell, in addition to the sensitive bar, prevents physical contact between the door leaf in motion and the obstacle, blocking the door instantly and reversing its motion in order to ensure the function and durability of the sensitive bar.

All doors model SC are in compliance with standard EN 13241-1 and 1 and are subject to initial type testing by a notified organization that has issued the marking. Therefore, all doors are marked with an identification label with the marking.

Door for “Controlled Atmosphere” cold rooms for preservation and ripening where the internal temperature is not lower than -5°C; it guarantees the hermtic seal of the cold room.

A - Frame in plastic material internally reinforced in steel, white, with gasket tightening handwheels to ensure the gas seal.

B - Leaf consisting of a sandwich in prepainted sheet RAL 9010 insulated with PUR density 41 kg/m3, perimetric rim in aluminium with a gas seal gasket along its perimeter, with a standard thickness of 9 cm. An inspection porthole cm 70 x 90 H is mounted on the door leaf.

C - Sliding Rail in anodized aluminium with carter.

D - Back rail for sliding and regulation, wall mounted; it enables the sliding motion and the seal of the gasket, without additional accessories mounted to the floor that could be obstructive.

E - Threshold, connected to the frame, can be in 2 different types according to the required use of the door.

F - Internal frame placed on the internal side of the cold room permits rapid fastening to the prefabricated panels.

The sliding doors series SC 09 TNG with rail passage suitable only for positive temperatures, consists of 6 main parts as described below.

A - Standard frame in plastic material, internally reinforced in steel, colour white.

B - Standard leaf consisting of a sandwich panel in prepainted sheet RAL 9010 insulated with PUR density 41 kg/m3, perimetric rim in anodized aluminium with a seal gasket along its perimeter.

• Thicknesse available: 9 cm.

C - Standard sliding rail in anodized aluminium with carter in white prepainted aluminium.

D - Standard back rail for sliding and regulation, wall mounted, in anodized aluminium; it enables the sliding motion and the seal of the gasket, without additional accessories mounted to the floor that could be obstructive.

E - Threshold, connected to the frame, can be in 4 different types according to the required use of the door.

F - Internal frame in plastic material, colour white, placed on the internal side of the cold room, it permits rapid fastening to the prefabricated panels.

Series SC.L sliding doors available for temperatures above +4°C with ΔT < 16°C with Relative Humidity < 60%.

SCL sliding doors consisting:

A - Standard frame consisting of a sandwich panel in prepainted sheet (RAL 9010) insulated with PUR density 4 KG/m3, perimetric rim in anodized aluminium with a seal gasket along its perimeter. Thickness 7 cm.

B - Sliding system (Rail + Glider) in anodized aluminum.

C - Fixed external handle, in composite plastic material with grip in AISI 304 stainless steel piping.

D - Fixed internal handle in luminescent plastic material.

E - Lower rail system in stainless steel.

F - Rim hole door (optional) in AISI 304 stainless steel U-shaped section bars.

A - Standard white plastic frame reinforced internally with steel.

B - Standard leaf consisting of a sandwich panel in prepainted sheet RAL 9010 insulated with PUR density 41 kg/m3, perimetric rim in anodised aluminium with a sealing gasket along its perimeter. 9 cm thick only version TN.

C - Standard sliding rail in anodized aluminium complete with casing.

D - Standard back rail for sliding and regulation, wall mounted, in anodized aluminium.

E - Internal frame in white plastic, positioned on the inside of the cold room, allowing rapid fastening to the prefabricated panels.

Types of operation

• Manual with independent movement of the doors.
• Manual with simultaneous movement of the doors.
• Automatic with simultaneous movement of the doors.

A - Standard frame in plastic material, internally reinforced in steel, colour white; in the low temperature version it is equipped with anticondensation heating cable.

B - Standard leaf consisting of a sandwich panel in prepainted sheet RAL 9010 insulated with PUR density 41 kg/m3, perimetric rim in anodised aluminium with a seal gasket along its perimeter.

Thicknesses available:

• 7 cm (mod.SC07)
• 9 cm (mod. SC09) for TN doors,
• for the low temperature versions the standard thickness is 12 cm (mod. SC12).

C - Standard sliding rail in anodized aluminium with carter in white prepainted aluminium.

D - Standard back rail for sliding and regulation, wall mounted, in anodized aluminium; it enables the sliding motion and the seal of the gasket, without additional accessories mounted to the floor that could be obstructive.

E - Threshold, connected to the frame, can be in 4 different types according to the required use of the door.

E - Internal frame in plastic material, colour white, placed on the internal side of the cold room, it permits a rapid fastening to the prefabricated panels.

PSI-F semi-insulating service doors are designed for indoor installation in conditioned areas with minimum working temperatures ≥ 12°C, ΔT ≤ 12°C, R.H. ≤ 60.

They can be supplied for installation on panel or on brick wall.

The semi-insulating doors of the PVV-PE & PVV-PEG line (to-and-from in high density polyethylene) are designed for installations in air-conditioned rooms with minimum working temperatures > 12 °C, ΔT < 12 °C, U.R. < 60% they can only be used as service entrances and not for uses requiring a hermetic and thermal seal.

They can be supplied for installation on panel or brick wall.

PVV-F & PVV-FG semi-insulating doors are designed for installation in air-conditioned rooms with minimum working temperatures > 12°C, ΔT < 12°C, R.H. < 60%.

They can only be used as service doors and not for uses requiring a hermetic or thermal seal.

They can be supplied for installation on panel or brick wall.